Myers 2NFL52-12-P4-02 Rustler Series 4″ Submersible Pump (1/2 HP, 230V, Single Phase, 2-Wire, 8 Stage, 10/12 GPM)

Myers 2NFL52-12-P4-02 Rustler Series 4″ Submersible Pump is constructed of stainless steel to maximum longevity. Self-lubricating impellers ensure consistent performance and reliability. Each pump is tested before leaving the factory allowing installation with confidence. Designed and manufactured by Pentair Myers, a trusted name in the industry.

**Picture is stock photo and may not match exactly**

Motor: 1/2 HP, 230V, Single Phase

Stages: 8

Operating Flow Rate: 10/12 GPM – See Flow Chart

Length: 23″

Discharge: 1-1/4″ NPT

Precision-engineered, corrosion resistant pumps in 5, 7/8, 10/12, 20, and 30 GPM deliver efficient, dependable performance even in rough, aggressive water. Heads to over 650 feet and capacities to 45 GPM. Built to deliver long-term, trouble-free service. These pumps feature the proven SignaSeal staging system. Floating impeller design resists sand and reduces sand locking.

Specifications:

• Shell: Stainless steel. Diameter: 3-7/8.
• Discharge: Fiberglass-reinforced thermoplastic.
• Discharge Bearing: Nylatron.
• Intermediate Bearing: (On larger units) polycarbonate, nitrile rubber and stainless steel.
• Impellers: Acetal.
• Diffusers: Polycarbonate.
• Suction Caps: Polycarbonate with stainless steel insert.
• Thrust Pads: Proprietary spec.
• Shaft and Coupling: Stainless steel.
• Intake: Fiberglass reinforced thermoplastic.
• Intake Screen: Polypropylene.
• Cable Guard: Stainless steel.
• Check Valve: Spring loaded check valve.
• Agency Listings: CSA

Applications:

Water systems for residential, industrial, commercial, multiple housing, and farm use

Features:

• Proven Staging System: Our proven SignaSeal staging system incorporates a harder-than-sand ceramic wear surface that when incorporated with our floating impeller design, greatly reduces problems with abrasives, sand lock-up and running dry.
• Discharge: Corrosion resistant fiberglass reinforced thermoplastic for durability in aggressive water. Large octagon wrench area for ease of installation.
• Discharge Bearing: Exclusive self lubricating Nylatron bearing resists wear from sand.
• Intake: Corrosion resistant fiberglassreinforced thermoplastic for durability in aggressive water.
• Shaft: Positive drive from 7/16 hexagonal heavy duty 300 grade stainless steel.
• Coupling: Stainless steel press fit to pump shaft. Couples to all standard NEMA motors.
• Shell: Crimped shell.
• Hardware: All screws, washers and nuts are corrosion resistant 300 grade stainless steel.
• Check Valve: Spring loaded check valve.
• Cable Guard: Corrosion resistant stainless steel guard protects motor leads. Tapered ends prevent pump from catching on well.
• Intake Screen: Molded-in screen.
• Pentek XE Series Motor: 2 and 3-wire NEMA standard all stainless construction water-filled motors

NOTE: Motor, Control Box or Magnetic Starter must be ordered separately, if ordering pump end only. Discharge NPT is 1-1/4″.

*Length and Weight are approximate. **For 10 GPM, 15 GPM and 20 GPM discharge is 1-1/4″ NPT. ***For 30 GPM and 50 GPM discharge is 2″ NPT. NOTE: On 2 HP and larger Pump, Motor, Control Box or Magnetic Starter must be ordered separately. Check Valve not included on 5 HP, 7-1/2 HP and 10 HP models. Check Valve not included on 50 GPM models. TrimLine version maximum outside diameter is 3-3/4″. Standard version maximum outside diameter on all models is 3-7/8″